Mighty Watt and Mighty Watt Plus Cartridge Heaters Introduction & Design Stock Items List Mighty Watt Plus Figure X, A & D Lead Variations Figure F, G & R Lead Variations Figure U Sheath Extension Figure E Epoxy Seal Figure M Immersion Heater Mighty Watt with Internal Thermocouple Figure T & other Terminal Seals Figure Y Terminals & Plug Terminations Figure W Flange, B & C Lead Protection & additional variations Bullet Cartridge & Drain Heaters Cartridge Immersion Heaters Specifications & Limitations Watt Density & other Selection Factors

Introduction | SST & QST Split Sheath Insertion Heaters | Maxi-Zone High Temperature Insertion Heaters | Bolt Heaters

Swaged-in double conductor stainless steel braid is internally connected for strength and full length flexibility. See chart below for the additional dimension the Mighty Watt Plus Figure F and Figure G adds to the sheath length of stock items. For non-stock single conductor braided lead protection, specify Figure H for straight exit, Figure J for right angle. When ordering non-stock Fig. F, G, H or J items, specify the overall sheath length. 14" high temperature (850 F/450 C) leads with 12" braid is standard. Specify additional length. * At lead end. Standard cold sections can be increased. Consult Ogden for metric diameter dimensions. Non-Stock Braided Lead Protection Dia. Minimum Unheated* Fig. F/H Fig. G/J 1/8" -- -- 1/4" 1" 1" 5/16" 1" 1" 3/8" 1-1/2" 1-1/2" 1/2" 1-1/2" 1-1/2" 5/8" 1-9/16" 1-9/16" 3/4" 1-7/8" 1-7/8" 15/16" 1-7/8" 1-7/8" 1" 1-7/8" 1-7/8" 1-1/4" 1-7/8" 1-7/8" Add 3/8" to above dimension for total cold section at lead end. 2 Day Shipment Mighty Watt Plus Braided Lead Protection Dia. Adds to Length Fig. F Fig. G 1/4" 1/2" 9/16" 3/8" 1/2" 9/16" 1/2" 1/2" 5/8" 5/8" 1/2" 5/8" 3/4" 1/2" 5/8" Ordering Number Example: From Current Stock List: • 1/2" x 5-3/4" 1000W 240V • MWEJ05N0116 • Add 24" Fig. F Leads • MWEJ05N0116-F2 • (overall length now 6-1/4") • Using the same item, add 60" • • Fig. G leads • MWEJ05N0116-G5 • (overall length now 6-3/8")

Figure R is used when spacing requirements are limited. See chart below for the additional dimension the Mighty Watt Plus adds to the sheath length of stock items. When ordering non-stock Fig. R, specify the overall sheath length. High temperature (850 F/450 C) leads are fully flexible from the exit of the sheath. 12" lead wire is standard. Specify additional length. * At lead end. Standard cold sections can be increased. Consult Ogden for metric diameter dimensions. Non-Stock Right Angle Leads - Fig. R Dia. Minimum Unheated* 1/8" -- 1/4" 1" 5/16" 1-1/2" 3/8" 1-1/2" 1/2" 1-1/2" 5/8" 1-9/16" 3/4" 1-7/8" 15/16" 1-7/8" 1" 1-7/8" 1-1/4" 1-7/8" Add 3/8" to above dimensions for total cold section at lead end. 2 Day Shipment Mighty Watt Plus Right Angle Leads - Fig. R Dia. Adds to Lengh 1/4" 9/16" 3/8" 9/16" 1/2" 5/8" 5/8" 5/8" 3/4" 5/8" Ordering Number Example: From Current Stock List: • 1/2" x 5-3/4" 1000W 240V • MWEJ05N0116 • Add 24" Fig. R Leads • MWEJ05N0116-R2 • (overall length now 6-3/8")